Since 2006, Focus on rubber seals

The impact of seal damage on hydraulic equipment

by:ORK      2022-11-16
In the machining industry, hydraulic transmission is widely used, such as various semi-automatic hydraulic transmission lathes. During the use of these machine tools, failures such as impact and crawling often occur. When diagnosing and maintaining, the cause of the failure is often found on the hydraulic control components (such as various pumps and valves), resulting in the maintenance work being in trouble. In the end, such failures are often found in the actuators, that is, due to severe wear of the cylinder piston sealing elements. Such phenomena are especially“O”See more shape sealing rings. Example 1: A CB3463-1 program-controlled hexagonal turret semi-automatic lathe has a fault phenomenon that the feed speed of the turret tool post cannot be adjusted during use. The bottom of the oil cylinder can only stop, and the machine tool cannot be used normally. Seals Inspection and maintenance: Check all hydraulic control components, especially the speed control components, and found no problems. Replaced part of the speed control valve, the fault has not been eliminated. After dismantling and inspecting the cylinder, it was found that the piston“O”The seal ring is seriously worn, causing the hydraulic oil in the two chambers of the cylinder to channel each other. analyze the reasons for this“O”After the sealing ring is worn, the gap between the rod cavity and the rodless cavity of the cylinder increases and communicates. When the speed control valve 3 or the stop valve 2 is closed, it is equivalent to cutting off the oil return path of the rod cavity of the cylinder. Theoretically speaking, when the pressure oil enters the rodless cavity of the cylinder, a thrust F is formed on the piston, which makes the piston tend to move to the rod cavity. Back pressure, so that the two ends of the piston are balanced and stationary. At this time, F has = F has no, and the oil pressure without cavity is different due to the different force areas of the piston, that is, P has>P no. In practice, due to the interconnection between the two chambers of the cylinder, the pressure oil in the cylinder chamber tends to flow from the high-pressure area to the low-pressure area. As soon as the flow occurs, the pressure P in the chamber decreases, but P does not increase, and the thrust acting on both ends of the piston F none>F Yes, the piston loses balance and moves to the rod cavity to find a new balance point. In this way, the piston moves until there is an external force to stop it. The occurrence of the above phenomenon has a great impact on the maintenance work of the machine tool, and the replacement of the cylinder piston“O”After the sealing ring is removed, the failure of the machine tool is eliminated and the operation returns to normal. Example 2: A CE7120 hydraulic profiling lathe, during the work, the profiling tool holder leads the knife down and turns the longitudinal feed to cut the knife, resulting in frequent knife punching and scrapping, and the machine tool cannot work normally. Inspection and maintenance: Check that all hydraulic control components are free of faults, and the maintenance work will enter the blind spot for a while. Disassemble and inspect the longitudinal oil cylinder of the tool holder, and find the piston oil seal“O”The outer circle of the seal ring has been ground flat, and it is found that the outer circle of the piston does not meet the requirements (because of the machine tool manufacturing), the diameter direction is smaller than the standard size of 0.8mm, and the gap between the piston and the cylinder block is large, resulting in the intercommunication of oil between the two chambers of the longitudinal cylinder. At the time of maintenance, a qualified piston was replaced and“O”Troubleshooting of the punching tool of the machine tool after forming the sealing ring. The reason is analyzed that at the moment when the profiling tool rest is brought down and in place, the tool rest as a whole is subjected to an impulse F.’, after the force is decomposed, there is a horizontal thrust F’1 acts on the piston rod of the longitudinal oil cylinder, at the same time, the solenoid valve 34E1-25B works, the rod cavity of the longitudinal oil cylinder is connected to the pressure oil, the rodless cavity is connected to the return oil circuit of the speed control valve, and the force F of the rod cavity of the piston is connected by Two parts are completed, one is F’1, the other is F1=A1P1, where A1 is the force area of ​​the rodless cavity, then F=F’1+F1. Under normal circumstances, the piston starts to move to the rodless cavity under the action of the force F. Due to the incompressibility of the hydraulic oil, the pressure of the hydraulic oil in the rodless cavity suddenly rises to form a back pressure on the piston, and the piston is balanced by the speed regulating valve. Set the speed to move the knife smoothly. The moment has %F’1, the pressure P2 in the longitudinal cylinder cavity will be greater than P1. In practice, the two cavities of the cylinder are channeled due to the gap, and at P2>At the moment of P1, the hydraulic oil has a tendency to flow from the rodless cavity in the high pressure area to the rod cavity in the low pressure area. Once the flow occurs, P2 decreases, P1 increases, and F1 increases. Rodless cavity direction movement. After an instant, the horizontal thrust F acting on the piston of the longitudinal oil cylinder is due to the end of the downward movement of the profiling tool post.’1 disappears on its own, the rapid movement of the piston ends, the tool movement of the tool holder becomes stable, and the punching phenomenon ends. Company website: https://www.orksealing.com/
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...
Thank you for your enquiry. We will get back to you ASAP