The use skills and daily maintenance of vehicle rubber sealing strips

Vehicle rubber seals sealant strip is one of the key parts of vehicles. It is widely used in car doors, window glass, car body, seats, panoramic sunroofs, diesel engine boxes and car trunks. It can be produced and manufactured to install passenger cars. The vulcanized rubber seals door hinge of the trunk door of the car also has other functions such as moisture resistance and sealing. The usual maintenance and use skills of the vehicle window seal: 1. Check whether the seal has any large cracks or cracks. If the sealant is broken, it can be repaired with adhesive. It is very easy to use a special type of adhesive for sealing strips, and it is very easy to repair large cracks. Naturally, if the damage to the sealing strip is serious, or the embrittlement level is large, it is best to replace the new sealing strip for convenience. 2. After the car buyer uses the car detergent to clean the window, door and window seals, it is best to apply a layer of protective film with high water permeability, which can not only avoid the embrittlement of the sealant but also greatly improve the sealing effect. The tightness of the tape. 3. When disassembling and replacing all car bodies, a layer of sealant should be applied to the overlapped part of the welded steel bars. The thickness of the glue should be 2mm, and the glue should not have defects such as virtual sticking and bubbles. The ductile coating and anti-corrosion coating of 2mm-4mm should be applied on the lower layer of all wooden floors and the lower layer of the front tire cover. This countermeasure can not only greatly improve the airtightness of the whole vehicle and slow down the rust rate of the vehicle body, but also further improve the ride comfort. 4. The tightness of the car door and the car body is a relatively difficult position. The tightness regulations are relatively strict, and the part that should be sealed is relatively long. The cross-sectional appearance of each tightness position is different, and the car door is often opened and closed. In high-end cars, 3-way and 4-way seals are often set, and a four-fold seal structure is installed at the front support and the load-bearing beam on the top side of the car. This kind of multi-channel sealing is generally arranged in the front door frame. In addition to the sealing function, it also has the effect of sound insulation of the vehicle. 5. After the car window is damaged, the buyer should check whether the sealing tape is damaged when switching to laminated glass. Because the window glass usually does not respond to the original appearance after maintenance, at this time, in addition to ensuring that the car window can be easily driven or lifted, attention should also be paid to the airtightness around the car window. If the gap between the laminated glass and the slot hole of the laminated glass is not uniform, and the vulcanized rubber seals strip is loose with the laminated glass and the slot of the laminated glass, the car buyer can easily pull the sealing strip with force. 6. When the car buyer changes the top of the car, he should first apply a layer of conductive sealant near the top of the car, and then apply hemming glue to the water flow tank body and the interface after welding, which is not only conducive to The tightness of the car body can also avoid the initial rusting of the car body caused by the accumulation of water in the reverse side welding. 7. The sunroof is the basic equipment of most family cars. When the sunroof of the car is opened, the track of the silicone seal is exposed to the air, which will inevitably deposit smoke and dust, and even run into small gravel. Prolonged use will cause the panoramic sunroof to deform due to damage and block the drain pipe holes. Therefore, it is very important to remove the rails on time and to grease the rails. Although the vehicle window seal is a small component in the vehicle body, it can ensure that the power switch of the car door is stable and thick, and it can also protect the car from wind and rain, anti-fouling, heat insulation, sound insulation and noise reduction, and hand over the work of the window and door. The edging has the practical effect of a decorative design. When the car body is subjected to vibration and distortion, the sealing strip also has the functions of buffering, tearing resistance, and maintaining the laminated glass. Therefore, car maintenance is no big deal, and all stages cannot be ignored.
There are a lot of businesses today that are very much in demand and one of them is a rubber seals.
If you cannot find the specific type of that is best for your business in the above mentioned guide, you can visit ORK Rubber Seal Products for the best consultants specializing in this field, who can recommend the your are looking for. Customization is warmly welcomed here.
Ruichen Sealing Co., Ltd. can promise you that we never conceded on the quality standards of our products.
More than half of customers said they have faith with Ruichen Sealing Co., Ltd. and rubber seals.
Ruichen Sealing Co., Ltd. provides a way for you to understand your customers, to learn what makes them unique and what motivates their behavior. We can then leverage that wealth of information to personalize our interactions and demonstrate that rubber seals is valuable to our customers.